Amazonbasics Electronic Deadbolt Programming

Amazonbasics Electronic Deadbolt Programming

The AmazonBasics Electronic Deadbolt can be easily programmed by following a few simple steps. To program the lock, the user needs to enter the default Master Code, and then add new User Codes as required. The lock can store up to 20 User Codes. To delete a User Code, the user can enter the Delete User Code mode and follow the prompts. In case the user forgets the Master Code, the lock can be reset to the factory default settings. Overall, the programming process is straightforward and can be completed in a few minutes.

Execute the door handling identification procedure:

To perform the door handing identification process, follow these steps:

  1. Stand outside the door.
  2. Look at the door from the outside and locate the hinges.
  3. If the hinges are on the left side of the door, then the door is left-handed. If the hinges are on the right side of the door, then the door is right-handed.
  4. In case the door has a handle or knob, determine which side of the door it is on.
  5. If the handle or knob is on the left side of the door, then it is a left-handed door. If the handle or knob is on the right side of the door, then it is a right-handed door.

It’s important to identify the door handing correctly before installing a lock or latch. This will ensure that the lock or latch is installed correctly and functions properly.

How Can I Change My AmazonBasics Electronic Deadbolt’s Default/Existing Programming Code?

To change the default or existing programming code on your AmazonBasics Electronic Deadbolt, please follow these steps:

  1. Press and hold the Lock button for five seconds until the lock beeps and the LED light turns blue.
  2. Enter the current programming code and press the # key.
  3. The lock will beep twice to confirm.
  4. Press the 2 buttons and enter the new four to eight-digit programming code.
  5. Press the # key to confirm.
  6. The lock will beep twice to confirm. Repeat step 3 to program additional programming codes, up to 20 in total.
  7. Press and hold the Lock button for five seconds until the lock beeps and the LED light turns off.

It is recommended that you change the programming code periodically to ensure the security of your property. Be sure to choose a code that is easy for you to remember, but difficult for others to guess. Avoid using common codes like 1234 or 0000, and do not use codes that are related to personal information like birthdays or addresses.

Remove the Default User Code:

The AmazonBasics Electronic Deadbolt comes with a default Master Code (123456) and a default User Code (1111). To delete the default User Code, follow these steps:

  1. Enter the default Master Code (123456) and press the # key.
  2. Press the 3 buttons to enter the Delete User Code mode.
  3. Enter the default User Code (1111) and press the # key. The lock will beep twice to confirm that the User Code has been deleted.

It’s important to delete the default User Code to ensure the security of your property. It is recommended that you change the Master Code and program your User Codes to ensure that only authorized individuals have access to your property.

How Do You Add New User Codes to Your Electronic Keypad Deadbolt from AmazonBasics?

To add new user codes on your AmazonBasics Electronic Keypad Deadbolt, please follow these steps:

  1. Press and hold the Lock button for five seconds until the lock beeps and the LED light turns blue.
  2. Enter the current programming code (default is 123456) and press the # key. The lock will beep twice to confirm.
  3. Press the 1 button to enter the User Code mode.
  4. Enter a new four to eight-digit User Code and press the # key. The lock will beep twice to confirm.
  5. Repeat step 4 to program additional User Codes, up to 20 total.
  6. Press and hold the Lock button for five seconds until the lock beeps and the LED light turns off.

Make sure to choose a code that is easy for you to remember but difficult for others to guess. Avoid using common codes like 1234 or 0000, and do not use codes that are related to personal information like birthdays or addresses. It is recommended that you change the programming code and program your User Codes periodically to ensure the security of your property.

On your AmazonBasics electronic deadbolt, how do you disable or enable all user codes?

To disable or enable all User Codes on your AmazonBasics Electronic Deadbolt, please follow these steps:

  1. Press and hold the Lock button for five seconds until the lock beeps and the LED light turns blue.
  2. Enter the current programming code (default is 123456) and press the # key. The lock will beep twice to confirm.
  3. Press the 4 buttons to enter the Enable/Disable User Code mode.
  4. Press the 1 button to disable all User Codes. The lock will beep twice to confirm.
  5. Press the 2 buttons to enable all User Codes. The lock will beep twice to confirm.
  6. Press and hold the Lock button for five seconds until the lock beeps and the LED light turns off.

Disabling all User Codes can be useful if you want to temporarily restrict access to your property. Enabling all User Codes will allow all previously programmed User Codes to work again. Remember to choose a secure programming code and program your User Codes to ensure the security of your property.

How Do I Make a One-Time User Code for My Electronic Deadbolt from AmazonBasics?

To create a one-time User Code on your AmazonBasics Electronic Deadbolt, please follow these steps:

  1. Press and hold the Lock button for five seconds until the lock beeps and the LED light turns blue.
  2. Enter the current programming code (default is 123456) and press the # key. The lock will beep twice to confirm.
  3. Press the 1 button to enter the User Code mode.
  4. Enter a four to eight-digit User Code that will only be used once and press the * key. The lock will beep twice to confirm that the one-time User Code has been created.
  5. Give the one-time User Code to the person who will be using it.
  6. After the one-time User Code has been used, it will no longer work.

Creating a one-time User Code can be useful for granting temporary access to your property to guests, contractors, or service providers. It’s important to remember that the one-time User Code will only work once, so you will need to create a new one for each new person who needs access. Be sure to choose a secure programming code and program your permanent User Codes to ensure the security of your property.

Activating/Deactivating Auto-Lock:

To enable or disable auto-lock on your AmazonBasics Electronic Deadbolt, please follow these steps:

  1. Press and hold the Lock button for five seconds until the lock beeps and the LED light turns blue.
  2. Enter the current programming code (default is 123456) and press the # key. The lock will beep twice to confirm.
  3. Press the 2 buttons to enter the Auto-Lock mode.
  4. Press the 1 button to enable auto-lock. The lock will beep twice to confirm.
  5. Press the 2 buttons to disable auto-lock. The lock will beep twice to confirm.
  6. Press and hold the Lock button for five seconds until the lock beeps and the LED light turns off.

Enabling auto-lock will automatically lock the deadbolt after 30 seconds of inactivity while disabling auto-lock will require manual locking. It is recommended to enable auto-lock for maximum security, but it may be inconvenient in certain situations. Choose the option that best fits your needs and remember to choose a secure programming code and program your User Codes to ensure the security of your property.

How Do You Factory Reset Your Electronic Deadbolt by AmazonBasics?

To factory reset your AmazonBasics Electronic Deadbolt, please follow these steps:

  1. Remove the battery cover from the interior keypad.
  2. Remove the battery pack and disconnect the wire connector.
  3. Press and hold the Lock button for ten seconds.
  4. Reconnect the wire connector to the battery pack and reinstall the battery pack in the keypad.
  5. The deadbolt will beep twice to confirm that it has been reset to factory settings.

Factory resetting your AmazonBasics Electronic Deadbolt will erase all programmed User Codes and reset the programming code to the default code (123456). This should only be done as a last resort, as all programming will be lost, and the lock will need to be reprogrammed. Make sure to choose a secure programming code and program your User Codes after resetting the lock to ensure the security of your property.

Frequently Asked Questions and Troubleshooting Advice for Electronic Deadbolts from AmazonBasics:

Why isn’t working my AmazonBasics Deadbolt?

Your AmazonBasics Deadbolt may not be working due to several reasons, including dead batteries, a programming error, a malfunctioning motor, or a mechanical issue with the deadbolt. Check the batteries, ensure proper programming, and examine the lock mechanism to troubleshoot the issue. If you are unable to resolve the issue, contact the manufacturer or a professional locksmith for assistance.

Why can’t my AmazonBasics Keypad Deadbolt accept a new User Code?

You may not be able to add a new User Code on your AmazonBasics Keypad Deadbolt due to several reasons, including exceeding the maximum number of User Codes, a programming error, or a malfunctioning keypad. Check the user manual for the maximum number of User Codes that can be programmed, ensure proper programming, and try resetting the lock if necessary. If you are still unable to add a new User Code, contact the manufacturer or a professional locksmith for assistance.

How do I reset the electronic deadbolt on my Amazon Basics keypad?

To reset your AmazonBasics Electronic Keypad Deadbolt, remove the battery pack and disconnect the wire connector. Press and hold the Lock button for ten seconds, then reconnect the wire connector to the battery pack and reinstall the battery pack in the keypad. The deadbolt will beep twice to confirm that it has been reset to factory settings. This will erase all programmed User Codes and reset the programming code to the default code (123456). Be sure to program a new programming code and User Codes to ensure the security of your property.

Conclusion:

Programming your AmazonBasics Electronic Deadbolt is a simple process that can be done with just a few steps. You can change the default programming code, add or delete User Codes, enable or disable auto-lock, and create one-time User Codes. It is important to choose a secure programming code and program your User Codes to ensure the security of your property. If you encounter any issues, such as a malfunctioning keypad or motor, consult the user manual or contact the manufacturer or a professional locksmith for assistance. Finally, in case of a complete lockout or a forgotten programming code, you can factory reset your AmazonBasics Electronic Deadbolt to its default settings.

Wayne
Latest posts by Wayne (see all)