Schlage Lock Not Working After Battery Change

Schlage Lock Not Working After Battery Change? [Fixed]

Locks / By

Schlage locks are some of the most popular smart locks on the market. They’re also one of the most secure, with a wide range of features and customization options. But what happens when your Schlage lock stops working? You might be using wrong battery type or size, the compartment is not cleaned enough or maybe you need to perform a factory reset. Here’s how to deal with these issues and more. There are a few reasons why your Schlage lock may not work after changing the battery. Below are some of the most common causes and how to fix them.

Table Of Contents
  1. How to Restore a Schlage Lock that is Not Working after Battery Replacement?
  2. Frequently Asked Questions (FAQ’S)
  3. Final Thoughts

How to Restore a Schlage Lock that is Not Working after Battery Replacement?

There are a few reasons why your Schlage lock may not work after changing the battery. Below are some of the most common causes and how to fix them.

1. Make sure that Correct Battery Type Used

The most common issue is that the wrong type of battery was used. If you use a lithium battery, it won’t work with your lock. You need to replace it with an alkaline battery instead. Make sure that the batteries are installed correctly and that they are not damaged.

2. Check Whether the Batteries Are Wrongly Installed:

To check if the batteries are wrongly installed in your Schlage lock, you can follow these steps:

  1. Remove the battery cover on your Schlage lock using a screwdriver, if necessary.
  2. Take out the batteries and inspect them for any signs of damage or corrosion. If they are damaged or corroded, replace them with new batteries.
  3. Check the polarity of the batteries. The positive (+) and negative (-) ends should be inserted correctly in the battery compartment. Make sure that the ends are aligned with the markings on the compartment.
  4. If you are unsure about the polarity, refer to the instructions in the lock’s manual or look for markings inside the battery compartment that indicate which end is positive and which negative.
  5. Once you are sure that the batteries are properly aligned, reinsert them into the battery compartment.
  6. Put the battery cover back on and tighten the screws if necessary.
  7. Test the lock to see if it is working properly. If it is still not working, you may need to try other troubleshooting steps or contact Schlage’s customer support for further assistance.

3. Check that the Compartment is cleaned

If you replaced the batteries and your Schlage lock still does not work, make sure that the battery compartment is clean and free of corrosion or other blockages. If there is dirt in the compartment, clean it out with a cotton swab dipped in rubbing alcohol. Also make sure that your keypad is clean and dry before putting in new batteries. If there are any moisture or dust particles on your keypad, it will affect how well it works when you try to use it later on down the road.

If the problem persists after cleaning the compartment, it’s possible that one of the wires inside has come loose or disconnected from its contact point inside the lock mechanism. In this case, you’ll need to get a replacement part from Schlage customer service or a local locksmith who can repair your lock for you.

4. Make sure to check the Battery Terminals

Another thing you should do if your Schlage deadbolt isn’t working properly is check the battery terminals. If they’re corroded or dirty, this can lead to problems with electrical contact and prevent your lock from activating properly. You need to make sure that there is no corrosion or dirt buildup where the battery connects with each other — otherwise this could lead to intermittent operation or simply not working at all!

5. Attempt a factory reset to solve the issue

If you are having trouble with your Schlage keypad, it’s possible that a simple reset will fix the problem. To perform a factory reset:

  1. Remove the two screws at both ends of your Schlage deadbolt with a screwdriver.
  2. Push down on the top of the keypad and remove it from the back plate. You will see two wires connected to the circuit board inside. Unplug these two wires from their sockets on either side of the circuit board. You will also find some small black plastic clips holding them in place; use tweezers to gently pry these away from their sockets, then unplug them from their sockets.
  3. Now push down on each corner of your deadbolt until all four buttons click into place simultaneously (this should take about 10 seconds). You will hear a click when this happens. Your Schlage deadbolt should now be reset and ready for use again!

Frequently Asked Questions (FAQ’S)

1. Schlage deadbolt not working after battery change?

If your deadbolt is not working or locking, it could be due to a problem with the batteries. Make sure that you are using the correct type of batteries and that they are installed properly.

2. Schlage deadbolt keeps locking?

If your deadbolt keeps locking itself, there may be a problem with your lock itself. Check the batteries and make sure that they are installed correctly and fresh ones have been used. Try cleaning the exterior of the deadbolt with a damp cloth to see if that helps with any sticking issues. You may also want to remove any dirt or debris from around the door frame where it meets with the strike plate on your door. This will help prevent any further sticking problems from occurring in the future.

3. Why is my Schlage lock not working?

There are several reasons why your Schlage lock may not be working. Some of the most common reasons include:

Dead Batteries: If your lock is not working, the first thing to check is the batteries. If the batteries are dead or low, your lock may not function properly.

Battery Contacts: If the battery contacts inside the lock are dirty or corroded, this can prevent the lock from functioning properly.

Incorrect Programming: If the lock is not programmed correctly, it may not work. This can happen if you enter incorrect codes or if the lock’s programming has been reset.

Mechanical Failure: If there is a problem with the lock’s mechanical components, such as the latch or the internal gears, it may not function properly.

Electronic Failure: If there is an issue with the lock’s electronic components, such as the circuit board or the motor, it may not function properly.

Jammed Lock: If the lock is jammed or obstructed, it may not function properly.

If you have checked the batteries and battery contacts and ruled out incorrect programming or a jammed lock, it may be a mechanical or electronic failure. In this case, you may need to contact Schlage’s customer support or a professional locksmith for assistance.

4. How do you reset a Schlage lock after replacing the batteries?

Remove the battery cover from your Schlage lock using a screwdriver or by sliding it in the direction indicated by the arrows. Take out the old batteries and dispose of them properly. Inspect the battery contacts inside the battery compartment. If you notice any corrosion or rust, use a cotton swab or a soft-bristled brush to gently clean the terminals. Insert the new batteries into the battery compartment, making sure to align the positive (+) and negative (-) ends of the batteries with the markings inside the compartment. Hold the “Schlage” button on the keypad for 5 seconds or until the lock beeps and the status LED flashes red and green. Release the “Schlage” button and wait for the lock to reset, which may take up to 30 seconds. Once the lock has reset, it will beep three times, and the status LED will flash green three times. Test the lock to make sure it’s working properly.

If resetting the lock doesn’t resolve the issue, there may be another problem with the lock that requires further troubleshooting or professional assistance.

5. Why is my Schlage Lock code not working?

Possible reasons why your Schlage lock code is not working include incorrect code, low battery charge, dirty battery contacts, incorrect programming, a jammed lock, or a mechanical/electronic issue.

6. Schlage Turn Lock feature not working; what do I do?

To troubleshoot a Schlage lock turn lock feature not working:

  1. Check the batteries and replace them if necessary.
  2. Clean the lock to remove any dirt or debris that may be obstructing the lock.
  3. Check if the lock is correctly installed and aligned with the door.
  4. Test the lock to ensure it is functioning correctly.

If the issue persists, contact Schlage customer service or a locksmith for further assistance.

7. Schlage lock not working in the cold; what do I do?

If your Schlage lock is not working in the cold, it may be due to a few reasons. Here are some steps you can take to troubleshoot the issue:

Check the Batteries: Cold weather can drain batteries faster, so make sure that the batteries in the lock are fresh and fully charged.

Inspect the Lock: Check the lock for any obstructions that may be preventing it from working correctly, such as dirt or debris.

Check the Installation: Ensure that the lock is installed correctly and aligned with the door.

Lubricate the Lock: Apply a silicone-based lubricant to the lock to prevent freezing. Avoid using oil-based lubricants as they can attract dirt and debris.

Install Weatherstripping or Insulation: If the lock is exposed to extreme cold, consider installing weatherstripping or insulation to protect it from the cold.

Contact Schlage Customer Service or a Locksmith: If the lock is still not working, contact Schlage customer service or a professional locksmith for further assistance.

By following these steps, you may be able to troubleshoot the issue with your Schlage lock not working in the cold.

Final Thoughts

So there can be countless reasons due to which lock stops working even after battery change. We have listed all common issues related to Schlage Lock and how to fix them. Don’t worry and give this article a nice and quick read. Hope this helps you!

Wayne
Latest posts by Wayne (see all)

Related Posts